This configuring is normally done by your communications program such as wvdial. It may do much of it without even letting you know what it's done. In olden days it was done with the "stty" utility. If you set something manually with stty, the communications program may change the setting to something else so it's usually best to just let the communications program handle it. See What is stty ?
Flow Control for an explanation of
it. You should always use hardware flow control if possible. Your
communication program or "
getty" should have an option for
setting it (and hopefully it's enabled by default). It needs to be
set both inside your modem (by an init string or default) and in the
device driver. Your communication program should set both of these
(if you configure it right).
If none of the above will fully enable hardware flow control. Then you must do it yourself. For the modem, make sure that it's either done by the init string or is on by default. If you need to tell the device driver to do it is best done on startup by putting it in a file that runs at boot-time. See the subsection Boot-time Configuration You need to add the following to such a file for each serial port (example is ttyS2) you want to enable hardware flow control on:
stty -F /dev/ttyS2 crtscts or stty crtscts < /dev/ttyS2
If you want to see if flow control is enabled do the following: In minicom (or the like) type AT&V (or ATI4 on 3Com modems) to see how the modem is configured and look for &K3 (or &H1 on 3Com modems) which means hardware flow control. Then without exiting the communications program (such as minicom) see if the device driver knows about it by typing: stty -F /dev/ttyS2 -a. Look for "crtscts" (without a disabling minus sign). Remember that communication programs change these settings so you may want to check them after you have started up your communication program.
Besides flow control there is speed. See What Speed Should I Use with My Modem. There's also are parity and bits-per-byte settings. Normally the port is set by the communications program at 8N1 (8-bits per byte, No parity, and 1 stop bit). If you're running PPP then you must use 8N1. So if you get a complaint that it's not 8-bit clean then it's likely not 8N1 like it should be.
Normally a CD (Carrier Detect) signal (on the CD wire for an external modem) is required before a serial port can be opened. But if stty has negated clocal (-clocal), then the port requires CD raised for the port to open and remain open. Actually, a skilled programmer can write the program in such a way as to force the port to open even when CD and clocal say not to. So if stty shows -clocal then there might be a problem with opening the port. But for dial-in, in some cases you may want -clocal so that when the remote modem stops sending a carrier and CD drops, the port will close and terminate all processes running on it.
One way to keep CD raised is to send "AT&C" to the modem so that CD from the modem will always be on. CD always-on is fine for dial-out but for dial-in, the CD signal is sometimes (but rarely) used to detected an incoming call.
clocal may be asserted by default in recent serial drivers. Minicom raises clocal automatically when it starts up so there is no problem with it opening the port. But it restores the clocal setting to it's original when you exit minicom. But version 6.0.192 of Kermit hung when I set -clocal and tried to "set line ...".
stty is something like setserial but it sets the speed (baud
rate), hardware flow control, and other parameters of a serial port.
Typing "stty -F /dev/ttyS2 -a" should show you how ttyS2 is
configured. Most of the stty settings are for things that you never
need to use with modems. Many of the setting are only needed for
Text-Terminals (and some are only needed for antique terminals of the
1970s). Your communication package should automatically set up the
several settings needed for modems. For this reason you normally don't
need to use stty so it's not covered much in this Modem-HOWTO. But
stty is sometimes useful for trouble-shooting. More is said about
stty in the Serial-HOWTO or Text-Terminal-HOWTO..